Author Topic: System 6 Protection  (Read 15142 times)

Offline stickers

  • Idling (800 rpm)
  • *
  • Posts: 148
Re: System 6 Protection
« Reply #20 on: August 24, 2008, 12:38:50 AM »
icic..thks thks..

So the official quotation is about 300+....my SE say can get 200+. So I think..it is a good deal.

So as for now...3M is the preferred choice...than Tuff kote..anyone with better recommendation?

TIA  ::)

Bro, you can try this...

http://www.autofoam.com.my/

not sure if they are any good...now about this from hypertune magazine...

Offline Keromond

  • Idling (800 rpm)
  • *
  • Posts: 100
Re: System 6 Protection
« Reply #21 on: August 24, 2008, 07:58:59 AM »
Bro, you can try this...

http://www.autofoam.com.my/

not sure if they are any good...now about this from hypertune magazine...

Hi Bro..tks...I read the link u gave me...is more like..strengthening the car body...n also sound proofing etc?? but it does looks interesting..u keen ar?

Offline stickers

  • Idling (800 rpm)
  • *
  • Posts: 148
Re: System 6 Protection
« Reply #22 on: August 24, 2008, 12:21:30 PM »
Not at the moment bro.......just sharing wif you what I know.... ;D
But would appreciate feedback from you on this autofoam stuff if you decide you go ahead.

Offline clarence

  • Max Torque (4400 rpm)
  • ****
  • Posts: 1,579
Re: System 6 Protection
« Reply #23 on: August 24, 2008, 12:46:39 PM »
ar..ok....maybe I shd say, in terms of workmanship and quality, Tuff Kote has dropped...  maybe go for 3M.... is a better option

I can confirm that Tuff Kote workmanship and quality has dropped - very disappointing and regret paying top dollar to get my car Tuff Kote.

Many areas in the wheel arch were not fully coated leaving some bare metal exposed, which defeats the primary objective of getting my car Tuff Kote.

Offline limck007

  • Moderators
  • Mid Zone (3000 rpm)
  • *
  • Posts: 1,016
Re: System 6 Protection
« Reply #24 on: August 24, 2008, 05:10:37 PM »
I can confirm that Tuff Kote workmanship and quality has dropped - very disappointing and regret paying top dollar to get my car Tuff Kote.

Many areas in the wheel arch were not fully coated leaving some bare metal exposed, which defeats the primary objective of getting my car Tuff Kote.

looks like another branded product gone down the drain

Offline Keromond

  • Idling (800 rpm)
  • *
  • Posts: 100
Re: System 6 Protection
« Reply #25 on: August 24, 2008, 08:29:57 PM »
I can confirm that Tuff Kote workmanship and quality has dropped - very disappointing and regret paying top dollar to get my car Tuff Kote.

Many areas in the wheel arch were not fully coated leaving some bare metal exposed, which defeats the primary objective of getting my car Tuff Kote.

U got feedback to tuff kote n demand rework or wat? I will go for 3M under carriage coating then... but will still go for system 6 PPS....hopefully is still good

Offline carowner

  • Low End (2000 rpm)
  • **
  • Posts: 375
Re: System 6 Protection
« Reply #26 on: August 24, 2008, 08:44:58 PM »
I did used all their 3 products in my previous ride. Just know that every 6 months need to go back for recoating. Can bring up to them to recoat if there are areas not properly done.

Offline clarence

  • Max Torque (4400 rpm)
  • ****
  • Posts: 1,579
Re: System 6 Protection
« Reply #27 on: August 24, 2008, 08:49:49 PM »
And everytime you go back to recoat, you have to pay again (at least $50) or your Tuff Kote warranty will be void!

Offline Keromond

  • Idling (800 rpm)
  • *
  • Posts: 100
Re: System 6 Protection
« Reply #28 on: August 29, 2008, 12:37:03 AM »
Went to do my sys 6 today...like wat Clarence said....standard drop...in fact v bad,
I got some stain near the door edge...they actually never see it...n when I complain...he just say...too bad..cannot remove...just rub rub abit..how to come off  :mad:

then when I reach home...all my car handle area...full of scratches....Call them back..they say too deep wun be able to conceal or make nicer...I immediately screw that aunty on the phone, telling her how deep can it be...it is so obvious, lack of effort..then she say ask me bring back to do again.... overall exp....really sucks!

Offline clarence

  • Max Torque (4400 rpm)
  • ****
  • Posts: 1,579
Re: System 6 Protection
« Reply #29 on: August 29, 2008, 05:10:16 AM »
You can always bring it back to them to re-do, or ask for a partial refund for an unsatisfactory job done.