Author Topic: Latio in built Steering lock  (Read 25205 times)

Offline alangohek

  • Low End (2000 rpm)
  • **
  • Posts: 377
Re: Latio in built Steering lock
« Reply #20 on: October 07, 2008, 04:38:05 PM »
Hi Ender and guys,

Er, I don't know abt this feature at all.
How to use it?
What is ignition knob? Where is it?

Regards.
It is inbuilt into every modern car. The ignition knob is the knob you turned to start your engine.

Offline limck007

  • Moderators
  • Mid Zone (3000 rpm)
  • *
  • Posts: 1,016
Re: Latio in built Steering lock
« Reply #21 on: October 07, 2008, 06:11:21 PM »
The knob you turn to start engine.. 

My 1st post briefly describe how to activate  it. Basically once you off engine, turn the steering about 2 o'clock till your hear a click sound.

so to unlock>> must turn left and right BEFORE turning the switch rite????

Offline Ender

  • Mid Zone (3000 rpm)
  • ***
  • Posts: 452
Re: Latio in built Steering lock
« Reply #22 on: October 07, 2008, 09:56:51 PM »
so to unlock>> must turn left and right BEFORE turning the switch rite????

To unlock, turn right just a little, and turn your ignition knob forward to release.

Offline Ying

  • Mid Zone (3000 rpm)
  • ***
  • Posts: 845
Re: Latio in built Steering lock
« Reply #23 on: October 08, 2008, 11:02:52 AM »
small motorbike also have this feeature long time ago but you have to turn first then lock. I only use it on bike not car coz I dont like to turn steering when the car was parked.

Offline jaster

  • Cool Engine (0 rpm)
  • Posts: 5
Re: Latio in built Steering lock
« Reply #24 on: October 08, 2008, 03:51:38 PM »
small motorbike also have this feeature long time ago but you have to turn first then lock. I only use it on bike not car coz I dont like to turn steering when the car was parked.

same here, I don't like to turn the steering wheel too much when the car is parked and engine off. Isn't the steering wheel very heavy with the engine off, and hence the power steering off? newbie here so not very sure, but the chance is higher that something goes wrong and spoils with repeated turning with the power steering off, right?

I haven't tried the steering lock for my new car, but I always engage the steering lock on my old Nissan Micra ( when I was in UK), and it was a simple jiggle of the steering wheel when the wheels are straightened and the ignition key out of the socket.

Offline LatioR

  • Low End (2000 rpm)
  • **
  • Posts: 449
Re: Latio in built Steering lock
« Reply #25 on: October 08, 2008, 11:09:56 PM »
same here, I don't like to turn the steering wheel too much when the car is parked and engine off. Isn't the steering wheel very heavy with the engine off, and hence the power steering off? newbie here so not very sure, but the chance is higher that something goes wrong and spoils with repeated turning with the power steering off, right?

I haven't tried the steering lock for my new car, but I always engage the steering lock on my old Nissan Micra ( when I was in UK), and it was a simple jiggle of the steering wheel when the wheels are straightened and the ignition key out of the socket.

Hi jaster/all,

           It's perfectly ok (at least for me) to lock the steering (even purposely turn another 360 deg before turning to 2 clock direction, this is more effective way as mentioned by lyh1280) but do all of these before u turn off the engine lah... :smile:

Offline ben21

  • Cool Engine (0 rpm)
  • Posts: 33
Re: Latio in built Steering lock
« Reply #26 on: October 09, 2008, 09:29:02 AM »
Did something silly yesterday. Tried locking it but fail to read the second part about this threat on UNlocking it  ;)
Ok, so must "shake" it before turning the ignition. Will take this additional precaution in my Northern travel this weekend!

Offline Ender

  • Mid Zone (3000 rpm)
  • ***
  • Posts: 452
Re: Latio in built Steering lock
« Reply #27 on: October 09, 2008, 09:57:33 AM »
Did something silly yesterday. Tried locking it but fail to read the second part about this threat on UNlocking it  ;)
Ok, so must "shake" it before turning the ignition. Will take this additional precaution in my Northern travel this weekend!
You don't really have to shake. Just turn the wheel right a little bit and hold it to release the ignition knob.

Offline ben21

  • Cool Engine (0 rpm)
  • Posts: 33
Re: Latio in built Steering lock
« Reply #28 on: October 10, 2008, 11:36:34 AM »
Ahh, i see. Thanks!

Offline iagree

  • High End (5000 rpm)
  • *****
  • Posts: 3,621
  • iagree!
Re: Latio in built Steering lock
« Reply #29 on: October 11, 2008, 09:08:53 PM »
The knob you turn to start engine.. 

My 1st post briefly describe how to activate  it. Basically once you off engine, turn the steering about 2 o'clock till your hear a click sound.

Hi Ender

I see, this sound similar to my 1st Wira car in Msia. I will try that ... thanks for info.

Regards.
sorry, i must agree because i don't know how to disagree. agreeeee only....

from
   -iagree, must agree

Offline arias48

  • Low End (2000 rpm)
  • **
  • Posts: 306
Re: Latio in built Steering lock
« Reply #30 on: October 12, 2008, 12:27:45 PM »
Any recommendation for add-on steering lock?

Offline clarence

  • Max Torque (4400 rpm)
  • ****
  • Posts: 1,579
Re: Latio in built Steering lock
« Reply #31 on: October 16, 2008, 10:39:38 AM »
Actualy the best way to deter and delay vehicle theft is to remove the connection terminal at your battery after you have parked your car, so that your car cannot even be started. Which car thief would think that the battery terminals are disconnected or bother to open the bonnet to check?  ;D

Offline Ender

  • Mid Zone (3000 rpm)
  • ***
  • Posts: 452
Re: Latio in built Steering lock
« Reply #32 on: October 16, 2008, 12:10:31 PM »
Actualy the best way to deter and delay vehicle theft is to remove the connection terminal at your battery after you have parked your car, so that your car cannot even be started. Which car thief would think that the battery terminals are disconnected or bother to open the bonnet to check?  ;D

Thanks for your suggestion, but I think Mr Bean's method of removing the steering wheel is much more convienent. No need to open bonnet, no need of tools such as spanner, and no need to get hands dirty.

Offline clarence

  • Max Torque (4400 rpm)
  • ****
  • Posts: 1,579
Re: Latio in built Steering lock
« Reply #33 on: October 16, 2008, 01:28:06 PM »
There are such after market steering wheels available.

Offline LatioR

  • Low End (2000 rpm)
  • **
  • Posts: 449
Re: Latio in built Steering lock
« Reply #34 on: October 29, 2008, 11:51:34 PM »
hi all, still waiting for gd recommendation for gd steering lock lei! Cheap & gd one!

Offline Silver

  • Mid Zone (3000 rpm)
  • ***
  • Posts: 900
Re: Latio in built Steering lock
« Reply #35 on: October 29, 2008, 11:56:50 PM »
since you go Malaysia often, you can see what the Malaysians use in their cars
those should be good
Be safe. Go with the flo.

Offline iagree

  • High End (5000 rpm)
  • *****
  • Posts: 3,621
  • iagree!
Re: Latio in built Steering lock
« Reply #36 on: October 30, 2008, 08:43:12 AM »
Thanks for your suggestion, but I think Mr Bean's method of removing the steering wheel is much more convienent. No need to open bonnet, no need of tools such as spanner, and no need to get hands dirty.

Hi Ender  & Clarence & guys,

Huh, these ideas are superb. I like it.

But, if  we keep on removing & fixing back the steering, i think is more scary aso. What if one day we are blur king and din fix it back nicely and the whole steering drop out while we half way driving it... etc......

Regards.
sorry, i must agree because i don't know how to disagree. agreeeee only....

from
   -iagree, must agree

Offline LatioR

  • Low End (2000 rpm)
  • **
  • Posts: 449
Re: Latio in built Steering lock
« Reply #37 on: October 30, 2008, 08:42:35 PM »
since you go Malaysia often, you can see what the Malaysians use in their cars
those should be good

hi Silver, hv seen some real gd 1 but the price @~RM200 which i fd it too expensive. My previous 1 only cost me <RM$20 but very sad it's can't fit to Latio lei..

Offline Ender

  • Mid Zone (3000 rpm)
  • ***
  • Posts: 452
Re: Latio in built Steering lock
« Reply #38 on: October 30, 2008, 11:14:08 PM »
hi all, still waiting for gd recommendation for gd steering lock lei! Cheap & gd one!
I got mine for about $10 during an autobac sales.  But with a mallet, you can actually know out my lock. I think all those steering lock all can be disable with brute force. I still use it in malaysia as a deterrent, since it birght red, easily seen from outside. The real lock is the Latio own inbuilt steering column. This without i-key cannot unlock, if they use brute force, they may damage the steering column.

Offline clarence

  • Max Torque (4400 rpm)
  • ****
  • Posts: 1,579
Re: Latio in built Steering lock
« Reply #39 on: October 30, 2008, 11:25:43 PM »
As a further deterent against vehicle theft, you can choose to park head in and turn your steering wheel to the extreme right or left when parked.

This makes it more difficult for the thief to tow your car away.